Carr Lane (15)

Pallet fixture keys are designed for securing tooling plates and blocks to standard DIN pallets. Each pallet needs one centre key and one radial key for proper orientation. If needed, the radial key can be removed after the pallet is secured to the machine table. The threaded hole on top of each pin simplifies both insertion and removal. The centre keys featured here are compatible with 25, 30, and 50mm centre-hole diameters, while the radial keys are available for 20 and 25mm radial-hole diameters.

Palm-grip hand knobs come equipped with a full grip and fluted edge. Offered in two sizes, each available in blank, tapped, or reamed configurations. Tapped-hole sizes range from 3/8-16 to 5/8-11 (M10 to M16 metric), while reamed-hole sizes range from 3/8" to 5/8" (10mm to 16mm metric).

• External Diameter: 2-3/4 - 3-1/8
• Blank, Tapped and Reamed Holes

Carr Lane’s Pivoting Hoist Rings rotate 180° but do not spin. The standard Pivoting Hoist Rings featured in this range are durable and economical, offering a low profile and high load capacity. These hoist rings come in five sizes, with load capacities ranging up to 20,000 lbs.

• Load rating (lbs): 900kg to 9,100kg
• Thread x minimum length: M8 x 25mm to M16 x 65mm
• Base: Forged 1045 steel, black oxide finish
• Safety factor = 5:1.

Fast Lok and Scissor-Lok Plate Lifting Systems designed to be installed and to add/remove shackle assembly without tools

• Pivot a full 180°
• 10,000 lbs Load Capacity
• Patent pending

An effective tool used during the installation of Ball Plungers or Spring Plungers to make the process more efficient. Preferable to  a screwdriver on the ball/nose end, due to the clearance hole in the centre preventing the over-compression of the plunger's internal spring. Available in sizes to accommodate all Ball Plungers and Spring Plungers from #4-48 to 1"-8 (M4 to M12 in metric).

• Available in metric and Imperial sizing
• Sizes from #4-48 to 1”-8 (M4 to M12 in metric)

Press-fit ball plungers are perfect for use in softer materials like aluminium, wood, or plastic. They are ideal when a threaded hole isn't feasible or when no adjustment is needed. The sturdy shoulder ensures a secure seating position and effectively resists detent force. The installation hole can be counterbored to accommodate the shoulder. They are available in four different versions including steel stainless, steel steal with Delrin ball and stainless steel with Delrin ball

• Steel or Stainless Steel
• Choice of six sizes, two forces and a Stainless Steel or Delrin® Ball

• OD - 1"
• ID RANGE - .4724 - .7677"
• Imperial sizes available with a variety of Lengths

Carr Lane Press fit bushings are the most common yet most cost-effective type of drill bushing in the range. P-style drill bushings are the most common and cost-effective type of drill bushing. These bushings are permanently installed into the jig plate, typically flush with the top surface. Press fit bushings (P- style) bushings are primarily used for single-operation drilling or reaming, particularly when there is no expectation of replacing the bushings throughout the tooling's lifespan. They can be mounted closer together than headed bushings but provide less resistance to heavy axial loads. These are available in both ground and unground variants. Standard bushes are listed below however configurations are available on enquiry.

• OD - 1-1/2"
• ID RANGE - 1.0156 - 1.1417"
• Imperial sizes available with a variety of Lengths

Carr Lane Press fit bushings are the most common yet most cost-effective type of drill bushing in the range. P-style drill bushings are the most common and cost-effective type of drill bushing. These bushings are permanently installed into the jig plate, typically flush with the top surface. Press fit bushings (P- style) bushings are primarily used for single-operation drilling or reaming, particularly when there is no expectation of replacing the bushings throughout the tooling's lifespan. They can be mounted closer together than headed bushings but provide less resistance to heavy axial loads. These are available in both ground and unground variants. Standard bushes are listed below however configurations are available on enquiry.

• OD - 1-1/4
• ID RANGE - .8594 - .9449
• Imperial sizes available with a variety of Lengths

Carr Lane Press fit bushings are the most common yet most cost-effective type of drill bushing in the range. P-style drill bushings are the most common and cost-effective type of drill bushing. These bushings are permanently installed into the jig plate, typically flush with the top surface. Press fit bushings (P- style) bushings are primarily used for single-operation drilling or reaming, particularly when there is no expectation of replacing the bushings throughout the tooling's lifespan. They can be mounted closer together than headed bushings but provide less resistance to heavy axial loads. These are available in both ground and unground variants. Standard bushes are listed below however configurations are available on enquiry.

• OD - 1-1/8"
• ID RANGE - .7656 - .8465"
• Imperial sizes available with a variety of Lengths

• OD - 1-3/4"
• ID RANGE - .9843 - 1.3906"
• Imperial sizes available with a variety of Lengths

• OD - 1-3/8"
• ID RANGE - .6250 - 1.0312"
• Imperial sizes available with a variety of Lengths