Swing Clamps

ROEMHELD B1.848 Mini Swing Clamps with Sturdy Swing Mechanism: threaded-body type, double acting

• Maximum operating pressure 150 bar
• Maximum clamping force: 0.6 kN
• Rod diameter: 6 mm
• Piston diameter: 10 mm
• Clamping stroke: 6 mm

This double-acting mini swing clamp works as pull-type cylinder where a part of the total stroke is used to swing the piston. The clamping arms are locked on the piston rod. A safety screw avoids axial displacement.

ROEMHELD B1.849 Compact Swing Clamps: bottom flange, top flange, threaded-body type, single acting

• Maximum operating pressure 350 bar
• Maximum clamping force: 2.2 kN
• Rod diameter: 10 mm
• Piston diameter: 14 mm
• Clamping stroke: 6 mm
• Maximum flow rate: 2.5 cm³/s

ROEMHELD Compact Single-Acting Hydraulic Swing Clamps, threaded-body type with top and bottom flange used for clamping of workpieces when it is essential to keep the clamping area free of straps and clamping components for unrestricted workpiece loading and unloading.

ROEMHELD B1.8491 Compact Swing Clamps with Sturdy Swing Mechanism: bottom flange, top flange, threaded-body type, double acting

• Maximum operating pressure 350 bar
• Maximum clamping force: 2.2 kN
• Rod diameter: 10 mm
• Piston diameter: 14 mm
• Clamping stroke: 8 mm
• Maximum flow rate: 5 cm³/s

ROEMHELD Compact Hydraulic Swing Clamps with Sturdy Swing Mechanism used for clamping of workpieces when it is essential to keep the clamping area free of straps and clamping components for unrestricted workpiece loading and unloading.

ROEMHELD B1.8500 Swing Clamps with Sturdy Swing Mechanism: Top flange type, with optional position monitoring, double acting

• Maximum operating pressure 70 bar
• Maximum clamping force: 2 - 13.3 kN
• Rod diameter: 14 - 36 mm
• Piston diameter: 25 - 65 mm
• Clamping stroke: 8/10 mm
• Maximum flow rate: 13 - 167 cm³/s

The hydraulic swing clamp is a pull-type cylinder where a part of the total stroke is used to swing the piston. Due to the sturdy swing mechanism the angle position of the clamping arm remains the same after a slight collision with the workpiece during loading and unloading or during clamping. The angle position of the clamping arm is fixed with a dowel pin.

ROEMHELD B1.8510 Swing Clamps with Sturdy Swing Mechanism: Top flange type, with optional position monitoring, double acting

• Maximum operating pressure 120 bar
• Maximum clamping force: 3.4 - 22.8 kN
• Rod diameter: 14 - 36 mm
• Piston diameter: 25 - 65 mm
• Clamping stroke: 8/10 mm
• Maximum flow rate: 13 - 167 cm³/s

The hydraulic swing clamp is a pull-type cylinder where a part of the total stroke is used to swing the piston. Due to the sturdy swing mechanism the angle position of the clamping arm remains the same after a slight collision with the workpiece during loading and unloading or during clamping. The angle position of the clamping arm is fixed with a dowel pin.

ROEMHELD B1.852 Swing Clamps with Sturdy Swing Mechanism: Cartridge type, position monitoring optional, double acting

• Maximum operating pressure 350 bar
• Maximum clamping force: 6 - 22 kN
• Rod diameter: 16 - 32 mm
• Piston diameter: 23 - 45 mm
• Clamping stroke: 12 - 15 mm
• Maximum flow rate: 10 - 57 cm³/s

The hydraulic swing clamp is a pull-type cylinder where a part of the total stroke is used to swing the piston. The favourable area ratio (piston/piston rod) allows high clamping forces already at relatively low oil pressures. For high flow rates the swing speed is limited by an orifice in the clamping port. Thus, uniform clamping of several swing clamps is also possible when oil supply is effected through a common bore.

ROEMHELD B1.853 Swing Clamps with Sturdy Swing Mechanism: Top flange type, with optional position monitoring, double acting

• Maximum operating pressure 350 bar
• Maximum clamping force: 6 - 30 kN
• Rod diameter: 16 - 40 mm
• Piston diameter: 23 - 55 mm
• Maximum flow rate: 10 - 87 cm³/s

The hydraulic swing clamp is a pull-type cylinder where a part of the total stroke is used to swing the piston. The favourable area ratio (piston/piston rod) allows high clamping forces already at relatively low oil pressures. Due to the sturdy swing mechanism the angle position of the clamping arm remains the same after a slight collision with the workpiece during loading or unloading.

ROEMHELD B1.854 Swing Clamps with Sturdy Swing Mechanism: Bottom flange type, with optional position monitoring, double acting

• Maximum operating pressure 350 bar
• Maximum clamping force: 6 - 22 kN
• Rod diameter: 16 - 32 mm
• Piston diameter: 23 - 45 mm
• Maximum flow rate: 10 - 57 cm³/s

This hydraulic swing clamp is a pull-type cylinder where a part of the total stroke is used to swing the piston. The favourable area ratio (piston/piston rod) allows high clamping forces already at relatively low oil pressures. Due to the sturdy swing mechanism the angle position of the clamping arm remains the same after a slight collision with the workpiece during loading or unloading. 

ROEMHELD B1.880 Swing Clamps with Overload Protection Device: top flange, single and double acting

• Maximum operating pressure 500 bar
• Maximum clamping force: 2.8 - 41 kN
• Rod diameter: 20 - 50 mm
• Piston diameter: 25 - 63 mm
• Clamping stroke: 11 - 50 mm
• Maximum flow rate: 3 - 28 cm³/s

ROEMHELD B1.8801 Swing Clamps with Reinforced Swing Mechanism: top flange, position monitoring optional, double acting

• Maximum operating pressure 500 bar
• Maximum clamping force: 6.8 - 41 kN
• Rod diameter: 32 - 50 mm
• Piston diameter: 40 - 63 mm
• Clamping stroke: 20 - 22 mm
• Maximum flow rate: 20 - 55 cm³/s

Hydraulic swing clamps are used for clamping of workpieces when it is essential to keep the clamping area free of straps and clamping components for unrestricted workpiece loading and unloading.

ROEMHELD B1.8802 Swing Clamps with Reinforced Swing Mechanism: top flange, position monitoring optional, double acting, pendulum eye/fork head

• Maximum operating pressure 500/160 bar
• Maximum clamping force: 1.4 - 11.2 kN
• Rod diameter: 20 - 32 mm
• Piston diameter: 25 - 40 mm
• Clamping stroke: 22 - 25 mm
• Maximum flow rate: 8 - 20 cm³/s

The piston end of this swing clamp is designed as pendulum eye or fork head. By means of a double clamping arm 2 workpieces can be clamped at the same time. For both versions a springy element is required in order to maintain the double clamping arm in the unclamped position in horizontal position.

ROEMHELD B1.8803 Swing Clamps with Overload Protection Device: cartridge type, double acting

• Maximum operating pressure 500 bar
• Maximum clamping force: 6.8 - 41 kN
• Rod diameter: 20 - 50 mm
• Piston diameter: 25 - 63 mm
• Clamping stroke: 11 - 25 mm
• Maximum flow rate: 3 - 27 cm³/s

This hydraulic clamping element is a pull-type cylinder where a part of the total stroke is used to swing the piston.