Swiveling, Swing Clamps and Cylinders

Hilma Swiveling and Swing Clamps

Swiveling, Swing Clamps and Cylinders There are 9 products.

Showing 1 - 9 of 9 items
  • HILMA WZ 2.2185 Pivot and pull clamp double-acting, max. 400 bar

    • Max. clamping force: 104 - 160 kN
    • Clamping stroke: 10 mm
    • Tilting angle: 15°
    • Max. flow rate 16 cm³/s
  • HILMA WZ 4.2170 Swing Clamping Elements, this swivel and pull clamp is available in sizes 60, 104, 164 kN or 216 kN at 400 bar operating pressure., with flanged or pipe connection.

    • Max. clamping force: 60 - 216 kN
    • Piston diameter: 52 - 88 mm
    • Clamping stroke: 5 - 6 mm
    • Clamping edge: 18 - 28 mm
    • Swing angle: 90°
  • HILMA WZ 4.2150 Compact design Swing Sink Clamps installed in press rams or beds, used in machine tools and plants.

    • Max. clamping force: 60 - 216 kN
    • Piston diameter: 52 - 88 mm
    • Clamping and lowering stroke: 42 - 65 mm
    • Clamping edge: 18 - 50 mm
    • Swing angle: 2 x 45°
  • HILMA WZ 2.2230 Swing Sink Clamps for External Clamping, for fastening to a press bed and a press slide when the available space is limited

    • Max. clamping force: 104 - 216 kN
    • Clamping and lowering stroke: 105 - 112 mm
    • Swing angle: 2 x 45°
    • Max. clamping edge height: 68 mm
    • Max. flow rate 50 - 120 cm³/s
  • HILMA WZ 2.1833 Swivel and Pull Clamps for presses and high-speed punching presses when the available space is limited

    • Max. clamping force: 30.4 kN
    • Clamping stroke: 30 mm
    • Swing angle: 90°
    • Max. flow rate 15 cm³/s
  • HILMA WZ 2.2240 Double-acting Wedge Swing Clamps used on press beds and rams where space given is imited

    • Max. clamping force: 50 - 100 kN
    • Clamping stroke: 7.5 - 9.5 mm
    • Tilting angle: 15°
    • Max. flow rate 70 cm³/s

  • HILMA WZ 4.2180 Compact, Double Acting Pull Clamps for clamping dies on a press bed or press ram, used when space is limited.

    • Max. pulling force 60 - 164 kN
    • Piston diameter: 52 - 88 mm
    • Clamping stroke: 10 mm
    • Clamping edge: 28 - 48 mm
  • HILMA WZ 4.2350 Pull Clamp with T-Slot that facilitates a die standardisation by means of a T-slot bar or T-nuts on the die

    • Max. pulling force 55 - 144 kN
    • For T-slot: 18 - 28 mm
    • Piston diameter: 70 - 105 mm
    • Clamping stroke: 6 mm
  • HILMA WZ 4.2351 T-slot Pull Clamp facilitates a die standardisation by means of T-slot bars or T-nuts on the die

    • Max. pulling force 55 - 144 kN
    • For T-slot: 18 - 28 mm
    • Piston diameter: 70 - 105 mm
    • Clamping stroke: 6 mm

Showing 1 - 9 of 9 items