Work Supports

ROEMHELD B 1.9501 Threaded-Body Work Supports: with metallic wiper edge, 3 sizes, 3 types of function, single acting

• Maximum operating pressure 500 bar
• External thread: M45 - M90
• Maximum load force: 16.8 - 102 kN
• Plunger diameter: 20 - 50 mm
• Plunger stroke: 12 - 20 mm
• Maximum flow rate: 25 - 100 cm³/s
• Elastic deformation: 1.8 - 4.5 µm/kN

In the body of the threaded-body work support a thin-walled locking bush is integrated, which locks cylindrically around the freely movable support plunger when pressurising the element with hydraulic oil. The elements are protected against penetration of swarf by a metallic wiper edge and sealed against liquids. The venting port allows also the connection of positive air pressure protection.

ROEMHELD B 1.9503 Work supports: Top flange type with metallic wiper edge, 3 sizes, 3 types of function, single acting

• Maximum operating pressure 500 bar
• Cross section of the body: 70x50 - 125x95 mm
• Maximum load force: 16.8 - 102 kN
• Plunger diameter: 20 - 50 mm
• Plunger stroke: 12 - 20 mm
• Maximum flow rate: 15 - 100 cm³/s
• Elastic deformation: 1.6 - 3.2 µm/kN

In the body of the work support a thin-walled locking bush is integrated, which locks cylindrically around the freely-movable support plunger when pressurising the element with hydraulic oil. The elements are protected against penetration of swarf by a metallic wiper edge and sealed against liquids. The venting port allows also the connection of positive air pressure protection.

ROEMHELD B1.9402 Threaded Body Work Supports: M 30 x 1.5, with metallic wiper edge, 4 sizes, double acting

• Operating pressure 500 bar maximum
• Maximum load force: 6.5 - 9.5 kN
• Plunger stroke: 8 - 15 mm

In the body of the threaded-body work support a thin-walled locking bush is integrated, which locks cylindrically around the freely-movable support plunger when pressurising the element with hydraulic oil. The support plunger is extended and retracted by means of a small double-acting cylinder. The threaded-body work supports are protected against swarf by a metallic wiper and sealed against liquids.

ROEMHELD B1.940 Single Acting Threaded Body Work Supports

• Maximum operating pressure 500 bar
• M30 external thread
• Maximum load force: 6.5 - 9.5 kN
• Plunger diameter: 16mm
• Plunger stroke: 8 - 15mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 4 µm/kN

Hydraulic work supports are used to provide a self-adjusting rest for the workpiece during the machining operations. They compensate the workpiece surface irregularities, also deflection and vibration under machining loads. Two sizes are available. The threaded-body design of the elements allows direct installation in clamping fixtures, in horizontal or vertical mounting position, and thereby a space-saving arrangement.

ROEMHELD B1.9401 Threaded Body Work Support: M 30 x 1.5, metallic wiper edge, 2 sizes, 3 types of function, single acting

• Maximum operating pressure 500 bar
• Cross section of the body: 70x48 - 140x105 mm
• Maximum load force: 8 - 40 kN
• Plunger diameter ranges from 16 to 40 mm
• Plunger stroke: 8 - 20 mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 0.7 - 1.0 µm/kN

In the body of the threaded-body work support a thin-walled locking bush is integrated, which locks cylindrically around the freely-movable support plunger when pressurising the element with hydraulic oil.

ROEMHELD B1.950 Single Acting Threaded Body Work Supports

• Maximum operating pressure 500 bar
• External thread: M45 - M90
• Maximum load force: 16.8 - 102 kN
• Plunger diameter: 20 - 50 mm
• Plunger stroke: 12 - 20 mm
• Maximum flow rate: 25 - 100 cm³/s
• Elastic deformation: 1.8 - 4.5 µm/kN

Hydraulic work supports are used to provide a self-adjusting rest for the workpiece during the machining operations. They compensate the workpiece surface irregularities, also deflection and vibration under machining loads.

ROEMHELD B1.942 Threaded Body Work Support: M 40 x 1.5, with metallic wiper edge, single acting

• Maximum operating pressure 500 bar
• External thread: M40
• Maximum load force: 15 - 20 kN
• Plunger diameter: 20 mm
• Plunger stroke: 10 - 15 mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 2.7 µm/kN

ROEMHELD B1.914 Work Supports: Extending hydraulically – contact by spring force, double acting

OBSOLETE ITEM - CONTACT HYQUIP

• Maximum operating pressure 500 bar
• External thread: M68
• Maximum load force: 20 kN
• Plunger diameter: 32 mm
• Plunger stroke: 12 mm
• Maximum flow rate: 35 cm³/s
• Elastic deformation: 1.3 µm/kN

Work supports are used to provide a self-adjusting rest to avoid deflection and vibration of the workpieces during machining. It is recommended to use double-acting elements if applied in larger hydraulic clamping fixtures with long lines, especially if the return oil is cycled and has to return in a predetermined time.

ROEMHELD B1.910 Work Supports: Extending hydraulically – contact by spring force, single acting with spring return

• Maximum operating pressure 500 bar
• External thread: M78
• Maximum load force: 48 kN
• Plunger diameter: 40 mm
• Plunger stroke: 18 mm
• Maximum flow rate: 70 cm³/s
• Elastic deformation: 1 µm/kN

With the B1910 range the support plunger is retracted in off-position. When pressurised the support plunger moves against the inserted workpiece by means of spring force. With increasing oil pressure, the plunger locks hydraulically. After the system has been unclamped, the support plunger returns to off-position. The support plunger is provided with female thread to enable the use of threaded pieces for height adjustment. 

ROEMHELD B1.9471 Threaded-Body Work Supports: with metallic wiper edge, double acting

• Maximum operating pressure 70 bar
• External thread: M26 - M45
• Maximum load force: 3 - 10 kN
• Plunger diameter: 10 - 16 mm
• Plunger stroke: 6,5 - 10 mm
• Elastic deformation: 5 - 9 μm/kN

The support plunger is hydraulically extended and retracted by means of a small double-acting cylinder. Contact to the workpiece is made by spring force. The pressure can be easily exchanged. Locking of the support plunger through the slotted clamping sleeve is made by means of a ringshaped conical hydraulic piston where the locking force is transmitted by a low-friction ball shell. Unlocking of the support plunger is made by spring force.

ROEMHELD B1.900 Work Supports: Off-position extended – contact by spring force, single acting

• Maximum operating pressure 500 bar
• External thread: M68 - M78
• Maximum load force: 32 - 48 kN
• Plunger diameter: 32 - 40 mm
• Plunger stroke: 16 - 18 mm
• Elastic deformation: 0.9 µm/kN

This spring-loaded plunger positions itself against the workpiece with an adjustable light spring force. Hydraulic locking is made together with hydraulic clamping of the workpiece, or independently. The support plunger is provided with female thread to enable the use of threaded pieces for height adjustment. Oil supply can alternatively be effected from the side or from below. The internal part of the work support is protected against dust and swarf by a sintered metal air filter. Recommended minimum pressure 100 bar.

ROEMHELD B1.911 Work Supports: Extending hydraulically – contact by spring force, double acting

• Maximum operating pressure 500 bar
• External thread: M78
• Maximum load force: 48 kN
• Plunger diameter: 40 mm
• Plunger stroke: 18 mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 1 µm/kN

Work supports are used to provide a self-adjusting rest to avoid deflection and vibration of the workpieces during machining. It is recommended to use double-acting elements if applied in larger hydraulic clamping fixtures with long lines, especially if the return oil is cycled and has to return in a predetermined time.