Roemheld (27)

ROEMHELD B1.940 Single Acting Threaded Body Work Supports

• Maximum operating pressure 500 bar
• M30 external thread
• Maximum load force: 6.5 - 9.5 kN
• Plunger diameter: 16mm
• Plunger stroke: 8 - 15mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 4 µm/kN

Hydraulic work supports are used to provide a self-adjusting rest for the workpiece during the machining operations. They compensate the workpiece surface irregularities, also deflection and vibration under machining loads. Two sizes are available. The threaded-body design of the elements allows direct installation in clamping fixtures, in horizontal or vertical mounting position, and thereby a space-saving arrangement.

ROEMHELD B 1.9472 Threaded-Body Work Supports with metallic wiper edge and long shaft, single and double acting

OBSOLETE ITEM - CONTACT HYQUIP

• Maximum operating pressure 70 bar
• Shaft length 20 – 100 mm
• External thread: M26
• Max. load force: 3 kN
• Plunger diameter: 10 mm
• Plunger stroke: 6.5 mm

The support plunger is hydraulically extended and retracted by means of a small single or double-acting cylinder. Contact to the workpiece is made by spring force. The pressure spring can be easily exchanged. The support plunger is additionally guided in the area of the shaft diameter and can therefore absorb side loads up to 300 N.

ROEMHELD B1.9470 Threaded-Body Work Supports: with metallic wiper edge, single acting

• Maximum operating pressure 70 bar
• External thread: M26 - M45
• Maximum load force: 3 - 10 kN
• Plunger diameter: 10 - 16 mm
• Plunger stroke: 6.5 - 10 mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 3.5 - 9 μm/kN

The support plunger is hydraulically extended by a small piston and contacts the workpiece with spring force. The pressure can be easily exchanged. Locking of the support plunger through the slotted clamping sleeve is made by means of a ring-shaped conical hydraulic piston where the locking force is transmitted by a low friction ball shell. Unlocking and retracting of the support plunger is made by spring force.

ROEMHELD B1.9401 Threaded Body Work Support: M 30 x 1.5, metallic wiper edge, 2 sizes, 3 types of function, single acting

• Maximum operating pressure 500 bar
• Cross section of the body: 70x48 - 140x105 mm
• Maximum load force: 8 - 40 kN
• Plunger diameter ranges from 16 to 40 mm
• Plunger stroke: 8 - 20 mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 0.7 - 1.0 µm/kN

In the body of the threaded-body work support a thin-walled locking bush is integrated, which locks cylindrically around the freely-movable support plunger when pressurising the element with hydraulic oil.

ROEMHLED F9.430 Threaded Coupling Elements

• Maximum operating pressure 500 bar
• Nominal diameter: ND 3 - 5
• Maximum flow rate: 9 - 15 l/min
• Coupling stroke: 4.5 mm
• Maximum coupling force 4.0 - 7.8 kN
• Positioning tolerance, axial: +0.5 mm
• Positioning tolerance, radial: ±0.1 - 0.2 mm

Compared to other coupling elements the threaded coupling elements are very compact devices. lf the slide movement of the workpiece carrier is to be used or if a fixture is to be connected to the base plate without lines, the threaded nipple and the coupling mechanisms can be directly screwed into the parts which are to be connected. The coupling mechanisms have the advantage that they are flush-faced in uncoupled mode. 

ROEMHELD M2.101 Tilting Module for universal use in assembly and handling processes in the industry

• Max. load 1,000 N, load balanced
• Tilting & Indexing Angle: 0 and 90°
• Max. load: 1000 N
• Max. torque: 500 Nm
• Max. balanceable moment: 180 Nm
• Operations: manual
• Operation indexing: pedal

ROEMHELD M2.201 Tilting module for universal use in assembly and handling processes in the industry

• Max. load 1,000 N
• Electrical operation
• Tilting angle: 0 to 90°
• Max. load: 1000 N
• Max. torque: 230 Nm
• Operations: foot switch or hand panel

Special hexagonal tower clamping system mechanical with fully machinable aluminium jaws

TMQS tower clamping system mechanical with fully machinable aluminium jaws.

ROEMHELD WS 4.3302 TS TriStar Tower Clamping Systems, mechanical-hydraulic, suited for at least 4 equal or different workpieces.

Max. Clamping Force

• TS 80 Tri Star: 20 kN at 45 Nm
• TS 100 Tri-Star: 25 kN at 55 Nm
• TS 125 Tri-Star: 40 kN at 115 Nm

Jergens clamping system mechanical with fully machinable aluminium jaws