Die Clamping Technology

HILMA WZ 8.18345 Spring-loaded ball and/or roller inserts with spring pack for istallation on presses without T-slots.

HILMA WZ 6.2276 Clamping Nut, Hydro-Mechanical with through-hole thread and optional clamping force display

with a tightening bolt:

• max. clamping force: 60 and 100 kN
• max.10 stroke: 2 mm
• exterior diameter 70 and 95 mm

with two tightening screws:

• max. clamping force: 60 to 150 kN
• max.10 stroke: 2 mm
• exterior diameter 70 up to 112 mm

HILMA WZ 3.2206 Single-Acting Angular Clamp with T-Slot Adaptor used for clamping and locking on machines and plants, suitable where space is limited

• Max. clamping force: 40 .. 110 kN
• For T-slot: 18, 22, 28 and 36 mm
• Clamping stroke: 2.5 .. 3 mm
• Max. temperature 120°C
• Max. operating pressure: 400 bar

HILMA WZ 2.2240 Double-acting Wedge Swing Clamps used on press beds and rams where space given is imited

• Max. clamping force: 50 - 100 kN
• Clamping stroke: 7.5 - 9.5 mm
• Tilting angle: 15°
• Max. flow rate 70 cm³/s

HILMA WZ 2.2407 Wedge Clamps for Tapered Clamping Edge double acting, max. clamping force 25 to 630 kN, with sequence valve control for high temperature ranges

• Max. clamping force: 25 .. 630 kN
• Adm. retaining force: 35 .. 820 kN
• Cylinder diameter: 25 .. 125 mm
• Clamping stroke: 20 .. 40 mm
• Max. temperature: 160/100 °C (300 °C on request)

ROEMHELD D8.021 Power Units, basic version

• Flow rate: 0.9 .. 6.2 l/min
• Operating pressure: 50 .. 500 bar
• Reservoir volume: approx. 11 l
• Usable oil volume: approx. 6 l
• Motor: 0.75 .. 1,5 kW – 400 VAC

HILMA RR 1.1560 Electric Control M1C and M2C for Magnetic Clamping Systems M-TECS

• The electric control M1C is used for small and medium-sized machines
• The electric control M2C is used for large machines
• Highest safety standards (as per EN 201/EN 289)
• Standardised integration via EUROMAP 70 interface
• Voltage: 380 ..480 VAC
• Frequency: 50/60 Hz
• Fuses: 32 A
• Code class: IP54

HILMA WZ 8.18347 Roller Conveyor Bar without hydraulic lifting but with the advantage of a high load-bearing capacity and a rugged construction

• Loads: 128 - 156 kN/m
• Roller spacing: 50 mm (other roller spacing on request)
• Segment length: 250 mm
• for T-slot: 22, 28 or 36 mm

Hilma Compact Clamping Claw with Movable Clamping Lever

HILMA WZ 4.2180 Compact, Double Acting Pull Clamps for clamping dies on a press bed or press ram, used when space is limited.

• Max. pulling force 60 - 164 kN
• Piston diameter: 52 - 88 mm
• Clamping stroke: 10 mm
• Clamping edge: 28 - 48 mm

HILMA WZ 3.1403 Single-acting Spring Clamping Cylinder, spring clamping, hydraulic unclamping

• Max. clamping force: 50 kN
• For T-slots: 22 - 28 mm
• Unclamping stroke: 2.5 mm
• Unclamping pressure: 175 bar

HILMA WZ 3.2206 Clamping Block for Angular Clamps, used for clamping and locking on machines and plants, suitable where space is limited

• Max. clamping force: 40 .. 110 kN
• For T-slot: 18, 22, 28 and 36 mm
• Clamping stroke: 2.5 .. 3 mm
• Max. temperature 120°C
• Max. operating pressure: 400 bar