Home

Tie rod single rod cylinder with position measurement system CST3

• Component series 3X
• Nominal pressure 160 bar
• Piston Ø 40 up to 200 mm
• Piston rod Ø 28 up to 140 mm
• Maximum stroke length 3000 mm

Bosch Rexroth Variable displacement axial piston pumps A4VBO open circuit

• Optimized high-pressure pump for maximum power requirement up to 500 bar
• Sizes 71, 125, 250, 450
• Nominal pressure 450 bar
• Maximum pressure 500 bar

HILMA WZ 2.2460 Wedge Clamps for Straight Clamping Edge double acting, clamping force 25 up to 100 kN, hydraulic clamping and unclamping, without and with position monitoring at the side

• Max. clamping force: 25 .. 100 kN
• Adm. retaining force: 45 .. 145 kN
• Cylinder diameter: 25 .. 50 mm
• Clamping stroke: 1 mm
• Temperature resistance: up to 100/160°C (on request: up to 300 °C)

ROEMHELD WS 4.3302 TS TriStar Tower Clamping Systems, mechanical-hydraulic, suited for at least 4 equal or different workpieces.

Max. Clamping Force

• TS 80 Tri Star: 20 kN at 45 Nm
• TS 100 Tri-Star: 25 kN at 55 Nm
• TS 125 Tri-Star: 40 kN at 115 Nm

ROEMHELD B1.900 Work Supports: Off-position extended – contact by spring force, single acting

• Maximum operating pressure 500 bar
• External thread: M68 - M78
• Maximum load force: 32 - 48 kN
• Plunger diameter: 32 - 40 mm
• Plunger stroke: 16 - 18 mm
• Elastic deformation: 0.9 µm/kN

This spring-loaded plunger positions itself against the workpiece with an adjustable light spring force. Hydraulic locking is made together with hydraulic clamping of the workpiece, or independently. The support plunger is provided with female thread to enable the use of threaded pieces for height adjustment. Oil supply can alternatively be effected from the side or from below. The internal part of the work support is protected against dust and swarf by a sintered metal air filter. Recommended minimum pressure 100 bar.

ROEMHELD B1.8802 Swing Clamps with Reinforced Swing Mechanism: top flange, position monitoring optional, double acting, pendulum eye/fork head

• Maximum operating pressure 500/160 bar
• Maximum clamping force: 1.4 - 11.2 kN
• Rod diameter: 20 - 32 mm
• Piston diameter: 25 - 40 mm
• Clamping stroke: 22 - 25 mm
• Maximum flow rate: 8 - 20 cm³/s

The piston end of this swing clamp is designed as pendulum eye or fork head. By means of a double clamping arm 2 workpieces can be clamped at the same time. For both versions a springy element is required in order to maintain the double clamping arm in the unclamped position in horizontal position.

ROEMHELD B1.5601 Built-in Anti-rotation Pistons: Piston and threaded bushing, complete with seals, double acting   Max. operating pressure 350 bar

• Maximum operating pressure 350 bar
• Piston diameter 32 - 50 mm
• Rod profile P3G: 22 - 40 mm
• Stroke 25 - 100 mm
• Maximum push force: 28.1 - 68.7 kN 

Pressure valves of type L-DB are pilot-operated pressure relief valves for a low preload pressure. 

• Size 40 ... 300
• Component series 3X
• Maximum operating pressure 25 bar
• Maximum flow 50000 l/min

The HYDAC ETS 3800 with VDMA menu navigation is a compact temperature switch for use with separate probes, offering a -30 to +150 °C range. It features intuitive setup, configurable outputs, and a rotatable 4-digit display for flexible installation.

Key Features:

• Measuring range¹) -30 .. +150°C (-22 .. 302°F)
• Display: 4-digit, LED, 7 segment, red, height of digits 7mm
• Connection, separate temp' probe Female cable connection: M12x1, 4 pole

Depending on the temp' range of the connected temp' sensor, the measurement range of the ETS 3800 may be reduced

• OD - 1-3/8"
• ID RANGE - .7188 - 1.0625"
• Imperial sizes with a variety of lengths

Carr Lane Head Press Fit Bushings are a variation of standard press fit bushings, featuring a head designed to withstand significant axial loads. These bushings are permanently installed into the jig plate and are typically used for single-operation drilling or reaming, where the bushings are not intended to be replaced throughout the tooling's lifespan. The head of these bushings can either remain exposed or be recessed by counterboring the installation hole.

• OD - 7/8"
• ID RANGE - .4921- .6562"
• Imperial sizes available with a variety of Lengths