Home

Filter elements for microfiltration, CELLUDISC type 46

Hengst - Formerly Bosch Rexroth Filtration

ROEMHELD M4.402 Solid Lifting Modules for high demands on performance and service life in the industrial assembly

• Max. lifting force 4,000 and 6,000 N
• Stroke from 200 to 400 mm
• Max. bending moment: 1000 Nm
• Operation: foot pedal
• Pump strokes per 100 mm: 7 - 9

ROEMHELD WS 5.358-Z Rapid Change Block Quintus for workholding systems MC, PC and SCS 3 sizes, with or without zero point clamping system

ROEMHELD B1.8268 Hinge Clamps 70 bar: with throttle valve, metallic wiper edge and optional position monitoring double acting

• Maximum operating pressure 70 bar
• Maximum clamping force: 2,6 - 12,1 kN - 1.3
• Maximum clamping force: 2.1 - 4.1 mm
• Adm. flow rate: 16 - 150 cm³/s

The hinge clamp is a double acting hydraulic cylinder with integrated clamping lever. When pressurising the element, the piston moves upwards and swivels the clamping lever over the hinges forwards and at the same time downwards onto the workpiece. The piston force is deviated by 180° and, depending on the lever length, the force is available as clamping force.

Carr lane miniature stainless steel slotted-heel clamp straps are equipped with a radius nose to provide firm workpiece contact. These clamp straps feature a slot underneath to slide straight back for easy loading. These are available to accommodate stud sizes ranging from #10-32 to 3/8-16, each in a choice of strap lengths. This clamp strap can be ordered individually or in a complete clamp assembly. The available assemblies are assembly with flange nut, assembly with spherical nut & washer, assembly with knurled knob and assembly with knurled knob & spherical washer.

• Thread - #10-32 - 3/8-16
• Length - 1-1/2 - 4
• Internal Diameter - 21/32 - 1-13/16
• Available with four assembly options to chose from

A practical hold-down clip designed to prevent Swivel Hoist Rings and Side-Pull Hoist Rings from rotating when not in use. Made of spring steel and zinc plated. Available in two sizes: one for ring diameters ranging from 3/8" to 5/8", and the other for ring diameters from 3/4" to 1-1/16".

 Carr Lane Diamond-Groove Bushings are manufactured for cast-in-place or potted setups. Their diamond-knurled outer diameter offers superior grip, resisting both rotational and axial forces effectively. As the outer diameter is not ground, it’s essential to precisely position the inner diameter during casting or potting to ensure the completed tool’s accuracy.

• OD - 5/8
• ID RANGE - .3125 - .4375
• Imperial sizes with a variety of lengths

• OD  - 1-3/4"
• ID RANGE - .9688 - 1.4062"
• Imperial sizes with a variety of lengths

• OD - 1/2"
• ID RANGE - .1405 - .3438"
• Imperial sizes with a variety of lengths

Enerpac remote / porting manifolds simplify valve and accessory mounting with VP-series valves and options

• Pressure: 350 bar
• Flow: 15 l/min

Carr Lane Head Press Fit Bushings are a variation of standard press fit bushings, featuring a head designed to withstand significant axial loads. These bushings are permanently installed into the jig plate and are typically used for single-operation drilling or reaming, where the bushings are not intended to be replaced throughout the tooling's lifespan. The head of these bushings can either remain exposed or be recessed by counterboring the installation hole.

• OD - 13/32"
• ID RANGE - .1870 - .2570"
• Imperial sizes available with a variety of Lengths

Carr Lane Press fit bushings are the most common yet most cost-effective type of drill bushing in the range. P-style drill bushings are the most common and cost-effective type of drill bushing. These bushings are permanently installed into the jig plate, typically flush with the top surface. Press fit bushings (P- style) bushings are primarily used for single-operation drilling or reaming, particularly when there is no expectation of replacing the bushings throughout the tooling's lifespan. They can be mounted closer together than headed bushings but provide less resistance to heavy axial loads. These are available in both ground and unground variants. Standard bushes are listed below however configurations are available on enquiry.

• OD - 3/8"
• ID RANGE - .1929 - .2500"
• Imperial sizes available with a variety of Lengths