Home

ROEMHELD B1.943 Threaded Body Work Supports 3 function types, with metallic wiper edge, optional contact control single acting

• Maximum operating pressure 500 bar
• External thread: M30 - M60
• Maximum load force: 6.5 - 42 kN
• Plunger diameter: 16 - 32 mm
• Plunger stroke: 8 - 16 mm
• Maximum flow rate: 25 cm³/s
• Elastic deformation: 2.5 - 3.5 µm/kN

In the body of the threaded-body work supports a thin-walled locking bush is integrated, which locks cylindrically around the freely-movable support plunger when pressurising the element
with hydraulic oil.

Index plungers are heavy-duty assemblies featuring a retractable, spring-loaded plunger and a corresponding locating bushing (sold separately). Tapered Index Plungers have a 15° taper on the plunger tip that matches the taper in the bushing, facilitating easier alignment and preventing binding during retraction. A straight plunger option is also available for slightly better positional accuracy. The plunger is fully retracted by a rotary-cam action when the handle is rotated 180°, with hardened steel cam surfaces for durability. The standard-mount configuration shown here includes a whistle notch on the Index Plunger to align with a setscrew. This configuration comes in three sizes, offering both inch and metric plunger diameters.

• Rotary Cam with Standard or Flange mount
• Available with Blank Machinable End
• Choice of 3 Plunger diameters
• Ground or Unground
• Tapered index plungers

Carr Lane Head Press Fit Bushings are a variation of standard press fit bushings, featuring a head designed to withstand significant axial loads. These bushings are permanently installed into the jig plate and are typically used for single-operation drilling or reaming, where the bushings are not intended to be replaced throughout the tooling's lifespan. The head of these bushings can either remain exposed or be recessed by counterboring the installation hole.

• OD - 1-3/4"
• ID RANGE - 1.0000 - 1.3906"
• Imperial sizes available with a variety of Lengths

Carr Lane Press fit bushings are the most common yet most cost-effective type of drill bushing in the range. P-style drill bushings are the most common and cost-effective type of drill bushing. These bushings are permanently installed into the jig plate, typically flush with the top surface. Press fit bushings (P- style) bushings are primarily used for single-operation drilling or reaming, particularly when there is no expectation of replacing the bushings throughout the tooling's lifespan. They can be mounted closer together than headed bushings but provide less resistance to heavy axial loads. These are available in both ground and unground variants. Standard bushes are listed below however configurations are available on enquiry.

• OD - 1-1/4
• ID RANGE - .8594 - .9449
• Imperial sizes available with a variety of Lengths

The entire range of NCB-series replacement chisels for Enerpac NC-Series nut splitters

• Splits hexagon nuts ranging from 10mm to 75mm diameter
• Cuts bolts ranging from M6 to M48 diameter
• Not to be used on square nuts

Turn Screw available in Quarter and Half turn type, ideal for swing-away lids and jig plates

• Thread: #10-24 - 1/2-13 or M5 - M12
• Metric and Imperial sizes

Carr Lane locking-pin bushings are compatible with Locking L Pins, Locking T Pins and Locking Clamping Pins. They are equipped with a retainer spring clip on the inside diameter, and is compatible with all types of locking pins and locating screws. These precision bushings are designed to be press-fitted into a standard reamed hole and can be securely fastened with a lock screw to ensure the bushing remains in place.

• Available in Metric and Imperial sizes
• Available in sizes from 3/16" - 1/2" (6mm-12mm)

Mini-size rest pad featuring an integrated swivel ball secured by a retaining ring. The gripper face is machined directly on the swivel ball. A built-in stop ensures the ball doesn't swivel beyond a certain point. Gripper Swivel Pads can be either surface-mounted or placed in a counterbored hole for installation. It is offered in body diameters ranging from 3/8 to 5/8" (10 to 17mm in metric).

• Thread: #4-40 - 1/4-28 or M4 - M6
• Metric and Imperial sizes
• Hardened Tool Steel (Serrated), Hardened Steel (Flat) and Delrin­® (Flat)

• Male Stud Coupling
• DIN 2353 / ISO 8434-1
• For use with Hydraulic Metric Seamless Carbon Steel Tube
• L Light Series from 6mm to 42mm OD
• S Heavy Series from 6mm to 38mm OD
• Pressure 100 bar to 630 bar, Subject to Series and Pipe Size!
• BSPP (G) Male End, Form E c/w WD Elastomeric Seal
• Zinc Plated with Trivalent Passivation
• Supplied with Tube Nut & Olive (Cutting Ring/Ferrule)

The HYDAC Filtromat OF 5 mini is a compact, stationary fluid care unit for bypass filtration, ideal for filling, repumping, and emptying hydraulic and lubrication systems. With a flow rate of up to 15 L/min, it delivers reliable oil cleanliness in a space-saving design.

Key Features:

• Flow rate: max. 15 l/min
• Operating pressure: max. 4.5 bar
• Convenient filtration in bypass flow

The HYDAC ALPC 9000 is a fully automatic particle counter for hydraulic and lubrication oils, offering fast, accurate analysis with minimal sample volume. Designed for labs, it supports up to 500 samples per day with ISO-calibrated precision and optional robotic automation.

Key Features:

• Sensor flow rate: 30 ml/min
• Permitted viscosity range: 1 ... 320 mm2 / s
• Measurement range (calibrated): ISO 0/0/0 ... 23/21/18