Home

ROEMHELD B1.827 Compact Clamps: Cartridge type, pneumatic position monitoring optional, double acting

• Maximum operating pressure 250 bar
• Max. clamping force: 2.5 - 10.5 kN
• Usable clamping stroke: 4.5 - 8.5 mm
• Adm. flow rate 4 - 25 cm³/s

The hydraulic compact clamp is a doubleacting pull-type cylinder where a part of the linear stroke is used to swing the clamping lever onto the workpiece. The version with cover is inserted in open bore holes and enables the smallest possible building height. The version without cover requires a closed pocket hole.

ROEMHELD B1.372 Low-Block Clamping Cylinder: single acting with spring return

OBSOLETE ITEM - CONTACT HYQUIP

• Operating pressure 500 bar maximum
• 3 sizes with maximum clamping forces ranging from 8.5 to 40 kN
• Piston diameter ranging from 16 to 36 mm
• Piston stroke 8 and 10 mm

The preferred application of low-block clamping cylinders are clamping situations where work holding from above is not possible or necessary. The low-clamping effect is caused by the downward motion of the clamping point while the high vertical force guarantees that the workpieces are safely held down.

ROEMHELD B1.552 Double-Acting Block Cylinders with Extended Piston Rods are used if one or several piston positions have to be controlled.

• Operating pressure 500 bar maximum
• Piston diameter ranges from 25 to 125 mm
• Rod diameter ranges from 16 to 80 mm
• Stroke ranges from 20 to 50 mm
• Maximum push force: 20.6 - 610 kN

The piston is equipped with a rod of diameter 10 mm that protrudes at the cylinder bottom. At this rod the customer can fix a control cam that is used to operate any limit switch or sensor. As an accessory a complete position monitoring system is available. This unit contains a control cam as well as two inductive proximity switches. The switches can be displaced in the housing which will be screwed to the bottom of the cylinder.

ROEMHELD B1.462 Plunger Piston with integrated pull-back spring, stroke limitation and fastening screw form a unit that cannot be disassembled.

• Max. operating pressure 250 bar
• Piston diameter: 25 - 50 mm
• Stroke: 8 and 12 mm
• Max. push force: 12.2 - 48.7 kN
• External thread: G1/8 - G1/2

The Equalizer Hydraulic Twin-Port Hand-Pump range is tailored for use with Equalizer International hydraulic equipment. The diaphragm oil-reservoir design means that, unlike conventional units, the hand-pumps are operable at all angles and are highly resistant to accidental spillage of hydraulic fluid.

Pressure valves of type ZDB10D and Z2DB10D are direct operated pressure relief valves in sandwich plate design

• Size 10
• Component series 2X
• Maximum operating pressure 350 bar
• Maximum flow 120 l/min

Enerpac compact, low-height telescopic cylinders are available with two or three pistons, and can lift loads up to 40 mm in a single movement.

• Capacity: 4,4 - 74,1 ton
• Stroke: 17 - 40 mm
• Max Pressure: 700 bar

ROEMHELD M8.203 Electrical Operating Elements, Lines and Connectors for the operation of electrical modulog modules, lifting modules and memory function.

ROEMHELD WS 5.3570 - Workholding Systems PC 80 mechanically operated, clamping against the fixed jaw or concentric clamping jaw

Max. Clamping Force:

• PC 80 F: 20 kN at 60 Nm
• PC 80 Z: 20 kN at 60 Nm

The Slotted-Heel Clamp Strap includes a replaceable clamping pad secured with two screws. The padded straps also accommodate custom pads or other attachments. These straps feature a slot underneath, enabling them to slide back easily for straightforward loading. Additionally, each side has a tapped hole at the rear for installing a Finger Pin. These available to accommodate stud sizes ranging from1/4-20 to 1/2-13 (M6 to M12 in metric), each in a choice of strap lengths. This clamp strap can be ordered individually or in a complete clamp assembly. The available assemblies are assembly with spherical nut & washer, assembly with flange nut, assembly with hand knob & spherical washer, assembly with acorn nut & spherical washer, assembly with bar knob & spherical washer and assembly with cam handle & spherical washer.

 Carr Lane Diamond-Groove Bushings are manufactured for cast-in-place or potted setups. Their diamond-knurled outer diameter offers superior grip, resisting both rotational and axial forces effectively. As the outer diameter is not ground, it’s essential to precisely position the inner diameter during casting or potting to ensure the completed tool’s accuracy.

• OD - 7/8"
• ID RANGE - .5000 - .6562"
• Imperial sizes with a variety of lengths